+37067100077

info@vitron.lt

Mn-Fr: 9:00 - 18:00

Trench heater with fan

Model VCV.090.260.2PH

Type of convector: VCV.90.260.2PH

Height: 90 mm.

Width: 260 mm.

Heat output :  (95/85/20 °C)  572 - 6064 W.

Standard length: 600-3000 (50 mm interval)

Trench heater with fan 90 260

 

Type Height [mm] Width [mm] Heat output Standard length [mm]
(95/85/20 °С) [W]
VCV.090.260.2PH 90 260 572 - 6064 600-3000 (50 mm interval)
Trench heater with fan

 

Trench heater with fan 90 260

 

VCV.090.260.2PH

(Heat exchanger 2 pipe, horizontal)

CharacteristicsHeat output W
Adjustable body height 0 - 40 mm.
Heat exchanger 2-pipe, horizontal
Heat exchanger length L- 350 mm.
Heat exchanger width 100 mm.
Heat exchanger height 50 mm.
Pipe diameter 15 mm.
Operating pressure 16 bar (1.6 MPa)
Connection 2 x G1 / 2"Connection 2 x G1/2' (internal thread)
Center distance of the heat exchanger pipes 50 mm.
Maximal heat transfer fluid temperature 95 °С
Voltage 220 V AC, 50 Hz

 

Heat output diagram VCV.90.260.2PH

 

Trench heater with fan 90 260 view

 

 

 

GuaranteesDesign featuresContents of deliveryDescription

The manufacturer provides the following warranty:

  • 10 years on a plate copper-aluminum heat exchanger;
  • 10 years for through corrosion of the convector body;
  • 1 year for fans and other used convector parts.

VITRON convector manufacturer reserves the right to change designs and prices without prior notice.

  • case material - galvanized steel 1 mm thick, coated with wear-resistant powder coating (coating color: matt black);
  • material and coating of grills - anodized aluminum, powder coated aluminum, wood (oak);
  • height adjustment from 0 to 40 mm due to special adjusting bolts;
  • heat exchanger connection - G1 / 2 ’’ (internal thread);
  • the use of materials with increased heat transfer properties (Cu - copper, Al - aluminum) and resistant to corrosion;
  • copper-aluminum heat exchanger coated with wear-resistant powder coating (coating color: matte black);
  • special adjustment screws make it easy to align the convector in a horizontal plane.
  • powder coated galvanized steel casing;
  • set of installation legs;
  • transverse or longitudinal grills;
  • decorative frame made of aluminum L and Z-shaped profile or edging of J and F-profile made in the color of the grille;
  • copper-aluminum heat exchanger (diameter of copper pipe 15 mm);
  • manual air vent G1 / 8 ’’;
  • technical passport, installation and operating instructions;

The VITRON forced-convector built into the floor is a heating device in which a copper-aluminum heat exchanger and a tangential fan are installed, the heat from which is transferred to the heated room by natural (with the fan turned off) and forced (with the fan turned on) convection. Allows blocking a stream of cold air from the glazed facades or windows. This type of convector are used for heating only dry rooms.

Combined use with underfloor heating, ventilation, radiator water heating systems is possible. It can be installed in both single-pipe and double-pipe heating systems.

 


© 2021 CONVECTOR VITRON. All data presented on the site are purely informational in nature and are not exhaustive. For more information, please contact the company's managers on the phone numbers listed on the website. All information provided on the website concerning a complete set, specifications, color combinations, and also cost of production has information character and under any conditions is not the public. These prices are recommended and may differ from the actual prices.

Please publish modules in offcanvas position.